Home News

Building a Test Probe Kit: Which Probes IEC 60529 and IEC 61032 Actually Call For

Building a Test Probe Kit: Which Probes IEC 60529 and IEC 61032 Actually Call For

Good quality IEC 60065 Standard for sales
Good quality IEC 60065 Standard for sales
Our goods has safely arrived at our residence. Thank you for your excellent services. I hope we can cooperate again in the future.

—— Wira

I'm Online Chat Now
Building a Test Probe Kit: Which Probes IEC 60529 and IEC 61032 Actually Call For

Most probe kits are bought by name and then found incomplete at the first audit. The reason is that the first IP digit and the access-probe family are two different systems that overlap: IEC 60529 defines four artefacts for the four digits, IEC 61032 defines a numbered probe family for shock protection, and product standards such as IEC 60335-1 and IEC 61010-1 borrow from both. A kit built from one list and audited against the other will always be missing something.

This article sets out what each artefact is for, what it is applied with, and where the two systems do not line up.

The four digits and the four artefacts

DigitArtefactForceSource
IP1X50 mm sphere with a 100 mm ring at the wrist50 NIEC 60529
IP2X12.5 mm sphere with a handle, or the jointed finger as an alternative30 NIEC 60529, IEC 61032 probe 2
IP3X2.5 mm diameter rod, probe C, with a stop face3 NIEC 60529
IP4X1.0 mm diameter wire, probe D, with a stop face1 NIEC 60529
Shock accessJointed test finger, 80 mm sphere, 12 mm by 80 mm finger, 80 mm to the stop faceSet by the product standard, from 10 N to 50 NIEC 61032 probe B

The ring on the 50 mm sphere is not decoration

The IP1X test uses a 50 mm sphere and a 100 mm diameter ring, and the ring is the part that makes the test repeatable. The sphere is pushed against the opening with 50 N; the ring stops the operator from pushing the sphere in by its own diameter. A sphere bought without the ring cannot limit insertion, and a laboratory that substitutes a plain steel ball will accept openings that the standard rejects. The same logic applies at IP3X and IP4X: the 2.5 mm rod and the 1.0 mm wire are delivered with a stop face, and the stop face is what converts a push into a measurement.

Three consequences follow. The ring has to be rigid enough not to flex at 50 N. The stop face has to be square to the axis within a visible tolerance, or the depth of insertion differs on four sides. And both have to survive being dropped, which is how most kits lose accuracy without losing parts.

Where the two systems do not line up

IP2X accepts either the 12.5 mm sphere or the jointed finger, and the two are not equivalent. The sphere tests a circular opening; the finger tests a slot, a louvre or a gap that a sphere cannot enter. A kit that carries only the sphere will pass a grille that the finger reaches through. Conversely, a kit that carries only the finger cannot apply the 30 N in the controlled way the sphere allows, because the finger has joints that take up the load.

The other mismatch is the force. IEC 61032 fixes geometry and only geometry. Force is set downstream: 50 N at IP1X, 30 N at IP2X, 3 N at IP3X, 1 N at IP4X, and for the jointed finger anywhere from 10 N to 50 N depending on the clause. That is why a kit needs force gauges as well as probes.

What a kit usually leaves out

  • The force gauges. A probe set with no way to apply a calibrated 30 N is a set of shapes. A push gauge with 1 percent accuracy covers the whole 1 N to 50 N range.
  • The 100 mm ring. Frequently lost, rarely replaced, and impossible to improvise at 50 N.
  • The 6.3 mm nozzle and the 12.5 mm nozzle. IPX5 and IPX6 are decided by a hose nozzle with a 6.3 mm bore delivering 12.5 l/min at 30 kPa, and IPX6 by a 12.5 mm bore at 100 l/min and 100 kPa. Nozzle bore wears, and a worn nozzle changes the flow that the test depends on.
  • A 20 mm clearance gauge. The distance from the nozzle to the enclosure is part of the test method, not a matter of convenience.
  • The verification record. Every artefact in the kit is a measuring instrument, and a kit without certificates is a kit that cannot be used in a report.

Buying order that survives an audit

Start with the artefacts the product standard names, not with the biggest set on offer. A laboratory testing household appliances needs the jointed finger and the 50 mm sphere long before it needs IP4X wire probes; a laboratory testing enclosures needs the four IP digits and the nozzles. The test probe and test sphere range lists each artefact with its standard reference and rated force, which is the only reliable way to match a purchase order to a clause. For the IP1X and IP2X geometry in detail, the note on the 50 mm sphere and its 100 mm ring covers what the dimensions are protecting.